Then after I finished checking the fluid level, I quickly sealed up the plugs, turned off the vehicle while it was still within the correct check temperatures according to the “A/T Temp” light. ScanGauge II Causes 'Phantom Error Codes' Says Toyota Discussion in Gen 1 Prius Plug-in 2012-2015 started by bfd. I recently did a flush and fill on the tranny, and I put the vehicle in “Transmission Temp Check Mode” to check the fluid level. 95 D60 scangauge kr fault codes Discussion in Trucks Eighteen Wheelers started by MKT. The only thing I’m wondering about now is how accurate they are. Thanks for this link! It definitely helped. “Transmission Fluid Temp -TFT” in the pan I assume I plugged in my scangauge and restarted the truck, it was only reading 93 degrees Fahrenheit! I wonder how accurate the people who used their scangauge to check fluid level are? Then after I finished checking the fluid level, I quickly sealed up the plugs, turned off the vehicle while it was still within the correct check temperatures according to the “A/T Temp” light. I recently did a flush and fill on the tranny, and I put the vehicle in “Transmission Temp Check Mode” to check the fluid level. No, there is no EGT sensor, and the Scangauge does not have a connection to. The only thing I’m wondering about now is how accurate they are. Does anyone know if there are any EGT or tranny temp codes available for a.
The second one I labeled TFT for the pan temperature. Hi, Im not sure where to put this thread, but I would like to let all of you who have been asking for new XGauge codes for the ScanGauge that we have 4.
Scangauge xcodes code#
The code I use as TCT fluctuates a lot, so I’m going with that one as the torque converter. Anyone running the scangauge with there truck an using x gauge commands If so please share the codes and what they are for. The information here applies specifically. It seems like there are two temperature sensors in the 2nd gen Tacoma Transmission. This document lists information for setting up common and useful XGauge parameters on the. 1 MKT Bobtail Member 15 3 0 Been googling for an hour trying to decipher fault codes from my scangauge KR but can't seem to find anything close to matching my codes on the dozen charts I've viewed.
Scangauge xcodes software#
Or you can disconnect both terminal leads and touch them together, personally I prefer the first option.Click to expand.Thanks for this link! It definitely helped. Enter the following two XGauge codes into your ScanGauge II (procedure will vary slightly depending on your SGII software revision). 95 D60 scangauge kr fault codes Discussion in ' Trucks Eighteen Wheelers ' started by MKT. Then after 10mins reconnect, then switch on ignition and clear the dtc's. ScanGauge XGauge Codes for Transmission Gear: High Road Travelers: Ford Motorhome Chassis Forum: 4: 02-02-2021 12:26 PM: Scan Gauge - Xgauge FrankO: Workhorse and Chevrolet Chassis Motorhome Forum: 17: 07-10-2009 02:41 AM: Codes that work for ScanGauge for 2004 W22 & Allison transmission: deputydog: Workhorse and Chevrolet Chassis Motorhome.
Disconnect the earth lead off the battery and press the brake a couple of times to discharge any stored capacitance. If the scangauge doesn't allow you to clear a dtc you can always do a hard reset. The scan shows me 2 errors, but when I press the clear button, it displays "no response".Īnother question: is there any drawback driving with EGR disconnected? Is there a risk to have the ECM switching to degraded mode? So I now decided to plug back the EGR and to switch off the MIL, using the Scangauge. Your ScanGauge features the exclusive X-GAUGE Programmable Gauge System that provides you a method to tap into additional information other than the standard built-in digital gauges.
Yesterday I drove my puma with EGR disconnected, and of course after the 3rd switch-on the MIL occured.Īccording to my Scangauge II fuel consumption measurement, it seems that I improved my MPG, but I did not feel any difference in the driving.
0 kommentar(er)
